Outdoor Lights On?? Configure Ubiquity If the theater has a second source of the same type, you will have more work to do, but if the activities above complete the programming of the Pronto, then you are ready to configure Ubiquity and it will be simple, also. Add a Remote You will get the Add a Remote pop-up menu shown below. Change the "Name" if you like, but the default will work unless there is already another remote by the same name in this room. At the bottom of the page, make sure "Controlled by and wire to " is checked.
For the address, enter The default set of IR codes that are in the file "Any Remote using Ubiquity ccf addr 83" is address If you are using the Sports Bar application, you will see that other code sets are available. The buttons in the middle of the menu represent the buttons of the remote control, meaning that the IR code that gets sent by the remote control is a number that is an index into this menu.
Then, each button uses the Action Tree to determine what to do - as illistrated by the names on the buttons below. You do not need to know any of this unless you have two sources of the same type e.
Click OK you may have to resize the windows task bar at the bottom of your display to get to the OK button. Note that this software releases requires that the actual name of the HVAC zone and Security System be configured into the menu. For those buttons that have question marks "? For example, the name "? Therefore, you would click on this button and use the Action Tree to set the thermostat in the zone in which the remote control is located to heating mode.
Note that if you are not using this remote control to control HVAC or security, then you do not need to do this step. There are just 2 steps. First, let's see how the existing source buttons work. Then, the button causes the Pronto to jump to the Transport page you can only see the first part of the destination of the jump in the example at the right so that the component can be controlled by the user.
Therefore, to control an additional AV source, start by duplicating one of the existing AV sources on the AV sources page. Next, click the "Appearance" tab at the top of the Button Properties menu. Note that the word "DVD" is part of the bitmap of the button image. Using the Label, you can add the 2 to the image or create a new image that looks a little better. That IR code is a reference into a table of actions.
That table is the set of button on the Remote Control menu of the Design Module the menu that looks like a field of buttons. Recall that the Pronto is sending out Destiny IR codes which are then modulated onto a radio frequency RF to be transmitted through the air.
Each code is unique and it is mapped to one of the buttons on the Ubiquity AV Remote Control menu the one that looks like a "field of buttons". Essentially, the IR code that is sent out is directly mapped to one of those buttons. Open "[Ubq]" the hidden one, not "RC-1 Extended" - the active one. Scroll down and open the "User 40, 41" page. Updated: June 11, Size: Requires firmware v3. Updated: December 07, Size: OLD VERSION Changes to this version include: improved performance and stability files load up to 30 times faster ; new shortcut keys and menus; graphical linking and improved button-to-button copying; button alignment and spacing tools; JPG support; redesigned IR code screens with IR duration; image extraction; plus other usability improvements.
Updated: June 21, Size: OLD VERSION Changes to this version include support for the TSU and RU, plus other changes made to v2: improved performance and stability files load up to 30 times faster ; new shortcut keys and menus; graphical linking and improved button-to-button copying; button alignment and spacing tools; JPG support; redesigned IR code screens with IR duration; image extraction; plus other usability improvements.
Updated: September 18, Size: Changes to this version include an improved installer, plus other changes made earlier: support for the TSU, improved performance and stability files load up to 30 times faster ; new shortcut keys and menus; graphical linking and improved button-to-button copying; button alignment and spacing tools; JPG support; redesigned IR code screens with IR duration; image extraction; plus other usability improvements.
The color screen, the pickup sensor, the RF base station, and the additional hard buttons are great improvements over the original version. Visit the RemoteCentral file download section to older versions of my CCF or to search for other component files. Visit the official Philips Pronto website for Pronto Edit software and firmware updates.
This alternative editor to ProntoEdit that works on all platforms Windows, Mac, Linux and has a few additional features not found in ProntoEdit. Note: This project is no longer active. Unfortunately, I was unable to get the battery pack to work with the ProntoPro, perhaps due to it producing lower voltage than the Philips battery pack. However, fully-functional extended batteries are available from ProntoWizard. Instead of making your own battery pack, I recommend just buying one.
If you want some general instructions for building your own, check out my partially successful Pronto Battery Assembly Guide. Vince, since I never got my batter pack to work, I removed that page from my site.
Sorry for any confusion. Please tell me the website about DIY batterr. I just need connector number and wire configuration. John, I republished my battery assembly instructions. I wish to download the Tonto installer for Windows. It does not seem to be available anywhere. Only the OS X version is available. May I request you for help in this matter. Tonto Download page. Eran: Go to the RemoteCentral. Any comparable devices I can use?
Generally, manufacturers tend to reuse codes for similar devices, but there is no way to know for sure what will work with your components unless you download them and give them a test.
Good Luck! A radio technology that allows you to control components not in direct line-of-sight, such as through walls or other obstacles. To keep your device up to date and enhance its functionality you can download new softwares that become available. Connect the device to the Internet, either directly or through a PC, and launch the upgrade utility. Color Liquid Crystal Display with touch screen input ensures better readability and the capability to visualize colour buttons and backgrounds.
Easy selection of buttons and commands is possible using the touch screen. Alpha blending is used to create the effect of transparency. It does this by combining a translucent foreground with a background colour to create an in-between blend. Backlighting is a feature that illuminates the LCD screen or keypad for use in the dark. Remotes backlit with LEDs are typically bright but uneven with a yellow or green color, while EL panels are smooth with blue, white or green shades.
Pick-up sensor is a feature that automatically activates the backlighting when the remote is moved or picked up. Timer functionality refers to a feature that allows a remote control to perform certain actions automatically at a predefined time.
To tailor the user interface to your local language, in the settings menu, select the language preffered. See all specifications See less specifications. Unfortunately this product is no longer available.
0コメント